1030013 – Sick

STOCK: 0.00 unidade(s)
ATM60-P4H13X13 Absolute Encoder 10-32VDC 8192Steps “Sick”

EAN: 4047084130717
Number of steps per revolution (max. resolution) 8,192 (13 bit)
Number of revolutions 8,192 (13 bit)
Max. resolution (number of steps per revolution x number of revolutions) 13 bit x 13 bit (8,192 x 8,192)
Measuring step 0.043°
Error limits G ± 0.25° 1)
Repeatability standard deviation sr 0.1° 2)
1)
In accordance with DIN ISO 1319-1, position of the upper and lower error limit depends on the installation situation, specified value refers to a symmetrical position, i.e. deviation in upper and lower direction is the same.
2)
In accordance with DIN ISO 55350-13; 68.3% of the measured values are inside the specified area
Communication interface PROFIBUS DP
Communication Interface detail DPV0
Data protocol Profile for encoders (07hex) – Class 2
Address setting 0 … 127, DIP switches or protocol
Data transmission rate (baud rate) 9.6 kBaud … 12 MBaud, automatic detection
Initialization time 1,250 ms 1)
Position forming time 0.25 ms
Status information LED green (operation), LED red ( bus activity)
Bus termination DIP switch 2)
Set (electronic adjustment) Via PRESET push button or protocol
1)
Valid positional data can be read once this time has elapsed.
2)
Should only be connected in the final device
Connection type Bus adapter for PROFIBUS 1)
Supply voltage 10 … 32 V
Power consumption = 2 W (without load)
Reverse polarity protection ?
MTTFd: mean time to dangerous failure 150 years (EN ISO 13849-1) 2)
1)
Order bus adapter separately.
2)
This product is a standard product and does not constitute a safety component as defined in the Machinery Directive. Calculation based on nominal load of components, average ambient temperature 40°C, frequency of use 8760 h/a. All electronic failures are considered hazardous. For more information, see document no. 8015532
Mechanical design Solid shaft, face mount flange
Shaft diameter 10 mm
Shaft length 19 mm
Weight 0.59 kg 1)
Shaft material Stainless steel
Flange material Aluminum
Housing material Aluminum die cast
Start up torque
2.5 Ncm (+20 °C), with shaft seal
0.5 Ncm (+20 °C), without shaft seal 2)
Operating torque
1.8 Ncm (+20 °C), with shaft seal
0.3 Ncm (+20 °C), without shaft seal 2)
Permissible shaft loading
300 N (radial)
50 N (axial)
Operating speed = 6,000 min?¹ 3)
Moment of inertia of the rotor 35 gcm²
Bearing lifetime 3.6 x 109 revolutions
Angular acceleration = 500,000 rad/s²
1)
Based on encoder with male connector.
2)
If the shaft seal has been removed by the customer.
3)
Allow for self-heating of 3.3 K per 1,000 rpm when designing the operating temperature range
EMC According to EN 61000-6-2 and EN 61000-6-3
Enclosure rating
IP67, with shaft seal (IEC 60529) 1)
IP43, without shaft seal, on encoder flange not sealed (IEC 60529) 1)
IP66, without shaft seal, on encoder flange sealed (IEC 60529) 1)
Permissible relative humidity 98 %
Operating temperature range –20 °C … +85 °C
Storage temperature range –40 °C … +100 °C, without package
Resistance to shocks 100 g, 6 ms (EN 60068-2-27)
Resistance to vibration 20 g, 10 Hz … 2,000 Hz (EN 60068-2-6)
eCl@ss 5.0 27270502
eCl@ss 5.1.4 27270502
eCl@ss 6.0 27270590
eCl@ss 6.2 27270590
eCl@ss 7.0 27270502
eCl@ss 8.0 27270502
eCl@ss 8.1 27270502
eCl@ss 9.0 27270502
eCl@ss 10.0 27270502
eCl@ss 11.0 27270502
eCl@ss 12.0 27270502
ETIM 5.0 EC001486
ETIM 6.0 EC001486
ETIM 7.0 EC001486
ETIM 8.0 EC001486
UNSPSC 16.0901 41112113