1123670000 – Weidmuller

STOCK: 0.00 unidade(s)
TRZ 230VUC 2CO Relay Module 2CO 8A 230VUC ±5% “Weidmuller”

TERMSERIES, Number of contacts: 2, CO contact AgNi, Rated, Continuous current: 8A, Tension-clamp connection, Test button available: No

Depth 87.8 mm
Depth (inches) 3.457 inch
Height 90.5 mm
Height (inches) 3.563 inch
Width 12.8 mm
Width (inches) 0.504 inch
Net weight 57.2 g
Storage temperature -40 °C…85 °C
Operating temperature -40 °C…60 °C
Operating temperature, min. -40 °C
Operating temperature, max. 60 °C
Humidity 5-95% relative humidity, Tu = 40°C, without condensation
Ambient temperature (operational), max. 60 °C
Output current derating (ohmic) 6 A @ 60 °C, 8 A @ 50 °C
Connection cross-section AWG, min. AWG 26
Connection cross-section AWG, max. AWG 14
Type of conductor rigid copper conductor, flexible copper conductor
Pollution severity level 2
Rated control voltage 230 V UC ±5 %
Rated current AC 5.5 mA
Rated current DC 4.4 mA
Power rating 1 W, 1.2 VA
Pull-in/drop-out voltage, typ. 125 V / 39 V AC
140 V / 30 V DC
Pull-in/drop-out current, typ. 2.3 mA / 0.6 mA AC
2.5 mA / 0.4 mA DC
Status indicator Green LED
Protective circuit Rectifier
Coil voltage of the replacement relay deviating from the rated control voltage Yes
Coil voltage of the replacement relay 110 V DC
Rated switching voltage 250 V AC
Continuous current 8 AOperating altitude = 2000 m, above sea level
Rail TS 35
Test button available No
Mechanical switch position indicator No
Colour black
UL94 flammability rating component
Component Housing
UL94 flammability rating V-0
Component Retaining clip
UL94 flammability rating V-0
Switch-off delay = 16 ms
Contact type 2 CO contact (AgNi)
Mechanical service life 30 x 106 switching cycles
Min. switching power 1 mA @ 24 V, 10 mA @ 10 V, 100 mA @ 5 V
Rated voltage 300 V
Pollution severity 2
Surge voltage category III
Clearance and creepage distances for control side – load side = 6 mm
Dielectric strength for control side – load side 3.51 kVeff /1 min.
Type of isolation at input and output reinforced insulation
Dielectric strength of neighbouring contacts 2.5 kVeff / 1 Min.
Type of isolation at neighbouring contacts Basic insulation
Dielectric strength of open contact 1 kVeff / 1 min
Dielectric strength to mounting rail 4 kVeff / 1 Min.
Impulse withstand voltage 6 kV (1.2/50 µs)
Protection degree IP20
Standards IEC 61810-1
Wire connection method Tension-clamp connection
Stripping length, rated connection 8 mm
Clamping range, rated connection 1.5 mm²
Clamping range, min. 0.14 mm²
Clamping range, max. 2.5 mm²
Wire connection cross section AWG, min. AWG 26
Wire connection cross section AWG, max. AWG 14
Wire cross-section, solid, min. 0.14 mm²
Wire cross-section, solid, max. 2.5 mm²
Wire cross-section, solid, min. (AWG) AWG 26
Wire cross-section, solid, max. (AWG) AWG 14
Wire connection cross section, finely stranded, min. 0.14 mm²
Wire connection cross section, finely stranded, max. 2.5 mm²
Wire cross-section, finely stranded, min. (AWG) AWG 26
Wire cross-section, finely stranded, max. (AWG) AWG 14
Wire connection cross-section, finely stranded with wire-end ferrules DIN 46228/4, min. 0.14 mm²
Wire connection cross-section, finely stranded with wire-end ferrules DIN 46228/4, max. 1.5 mm²
Conductor cross-section, flexible, AEH (DIN 46228-1), min. 0.14 mm²
Conductor cross-section, flexible, AEH (DIN 46228-1), max. 1.5 mm²
Twin wire-end ferrules, min. 0.5 mm²
Twin wire-end ferrules, max. 1 mm²
Blade size 0.6 x 3.5 mm
Gauge to IEC 60947-1 A1, B1