70122702 – Pepperl+Fuchs

STOCK: 0.00 unidade(s)
HiD2030 SMART Transmitter Power Supply Analog input “P+F”

2-channel isolated barrier
24 V DC supply (bus powered)
2-wire SMART transmitters or current sources
Usable as signal splitter (1 input and 2 outputs)
Dual output 4 mA … 20 mA or 1 V … 5 V
Line fault detection (LFD)
SIL 2 (SC 3) acc. to IEC/EN 61508

Safety Integrity Level (SIL) SIL 2
Systematic capability (SC) SC 3
Supply
Connection SL1: 1a(-), 1b(-); 2a(+), 2b(+)
Rated voltage 19 … 30 V DC bus powered via Termination Board
Rated current 37 mA at 24 V, 250 O load, 20 mA output (per channel)
Power dissipation 800 mW at 24 V, 250 O load, 20 mA output (per channel)
Input
Connection side field side
Connection SL2: 5a(+), 5b, 7a(-); 1a(+), 1b, 3b(-)
Input current 4 … 20 mA , current limit approx. 26 mA typ.
Input resistance < 40 O , for current source Ripple 10 mV eff Voltage min. 15.5 V at 20 mA Communication pass-through of HART signal to safe area The current sink terminals 4, 7 and 5, 6 do not pass HART signal to safe area. Output Connection side control side Connection SL1: 8a(+), 7a(-); 10a(+), 9a(-) Load 0 ... 650 O Output signal 4 ... 20 mA or 1 ... 5 V (on 250 O, 0.1 % internal shunt) Ripple 10 mV eff on a load of 250 O Response time 70 ms , 10 ... 90 % step change Signal level no fault: 1 mA ... 23.5 mA input current fault detection: < 0.2 mA or > 24 mA input current
Fault indication output
Connection SL1: 6b
Output type open collector transistor (common to both channels)
fault bus signal, collective error message
Transfer characteristics
Deviation at 20 °C (68 °F), 0/4 … 20 mA
= 20 µA incl. calibration, linearity, hysteresis, loads and fluctuations of supply voltage
Influence of ambient temperature = 2 µA/K
Frequency range field side into the control side: bandwidth with 0.5 Vpp signal 0 … 3 kHz (-3 dB)
control side into the field side: bandwidth with 0.5 Vpp signal 0 … 3 kHz (-3 dB)
Galvanic isolation
Input/Output basic insulation according to IEC/EN 61010-1, rated insulation voltage 300 Veff
Input/power supply reinforced insulation according to IEC/EN 61010-1, rated insulation voltage 300 Veff
Output/power supply basic insulation according to IEC/EN 61010-1, rated insulation voltage 300 Veff
Output/Output functional insulation, rated insulation voltage 50 V AC
Indicators/settings
Display elements LEDs
Control elements DIP switch
Configuration via DIP switches
Labeling space for labeling at the front
Directive conformity
Electromagnetic compatibility
Directive 2014/30/EU EN 61326-1:2013 (industrial locations)
Conformity
Electromagnetic compatibility NE 21:2017
EN 61326-3-2:2018
Degree of protection IEC 60529:2001
Protection against electrical shock UL 61010-1:2012
Ambient conditions
Ambient temperature -40 … 60 °C (-40 … 140 °F)
Relative humidity 5 … 90 %, non-condensing up to 35 °C (95 °F)
Mechanical specifications
Degree of protection IP20
Mass 140 g
Dimensions 18 x 114 x 130 mm (0.7 x 4.5 x 5.1 inch) (W x H x D)
Mounting on termination board
Coding pin 1 and 3 trimmed
For further information see system description.
Data for application in connection with hazardous areas
EU-type examination certificate CSANe 21 ATEX 2149 X
Marking Ex-Hexagon II (1)G [Ex ia Ga] IIC
Ex-Hexagon II (1)D [Ex ia Da] IIIC
Ex-Hexagon I (M1) [Ex ia Ma] I
Input Ex ia, Ex iaD
Voltage 26 V
Current 93 mA
Power 605 mW
Supply
Maximum safe voltage 250 V AC (Attention! Um is no rated voltage.)
Galvanic isolation
Input/input safe electrical isolation acc. to EN 60079-11:2007, voltage peak value 60 V
Input/Output safe electrical isolation acc. to IEC 60079-11:2007, voltage peak value 375 V
Input/power supply safe electrical isolation acc. to IEC 60079-11:2007, voltage peak value 375 V
Directive conformity
Directive 2014/34/EU EN 60079-0:2018 , EN 60079-11:2012
International approvals
CSA approval CoC 80072560 (cCSAus)
Control drawing 116-0486
IECEx approval
IECEx certificate IECEx CSAE 21.0010X
IECEx marking [Ex ia Ga] IIC , [Ex ia Da] IIIC , [Ex ia Ma] I
General information
Supplementary information Observe the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com.
Classifications
System Classcode
ECLASS 11.0 27210119
ECLASS 10.0.1 27210119
ECLASS 9.0 27210119
ECLASS 8.0 27210119
ECLASS 5.1 27210119
ETIM 8.0 EC001485
ETIM 7.0 EC001485
ETIM 6.0 EC001485
ETIM 5.0 EC001485
UNSPSC 12.1 32101514