ATV71HD45N4383 – Schneider
STOCK: 0.00 unidade(s)
Frequency inverter ATV71, 45kW, 60HP, 480V, EMC filer
Frequency converter for increased requirements 0.37 -630 kW. A complete offer: The devices in this series enable the control of asynchronous motors with vector-oriented flux control with or without speed feedback for powers of up to 2000 kW. Open to almost all communication networks. The Altivar 71 offers users advanced motor control modes and numerous flexible integrated functions to meet the most demanding requirements
Complex high-performance machines
Motor power (kW)
45 kW, 3 phases at 380-480 V
Engine power (HP)
60 hp, 3 phases at 380-480 V
max. motor cable length
100 m shielded cable
200 m unshielded cable
Supply voltage
380-480V -15 – +10%
Number of network phases
3 phases
Mains power
104 A for 380 V 3 phases 45 kW / 60 hp
85 A for 480 V 3 phases 45 kW / 60 hp
EMC filter
Integrated
Construction method
With heat sink
variant
Control synchronous motors with speed feedback
Apparent power
68.5 kVA at 380 V 3 phases 45 kW / 60 hp
Mains short-circuit current
22 kA for 3 phases
Rated output current
77 A at 2.5 kHz 460 V 3 phases 45 kW / 60 hp
94 A at 2.5 kHz 380 V 3 phases 45 kW / 60 hp
maximum peak current
141 A for 60 s 3 phases 45 kW / 60 hp
155 A for 2 s 3 phases 45 kW / 60 hp
Output frequency
0.1…500 Hz
Rated clock frequency
2.5kHz
Clock frequency
1 – 16 kHz adjustable
2.5 – 16 kHz with derating factor
Type motor control asynchronous motor
Vector-oriented flow control without encoder (SFVC) (voltage or current vector)
V/f characteristic (2 or 5 points)
Vector-oriented flow control (FVC) with encoder (current vector)
ENA system (energy adjustment) for asymmetrical loads
Polarization type
No impedance for Modbus
Additional features
Product determination
Synchronous motors
Asynchronous motors
Supply voltage limits
323…528 V
Frequency of power supply
50 – 60 Hz – 5 – 5%
Power supply frequency limits
47.5 – 63 Hz
Speed ??setting range
1…100 for asynchronous motor in positioning operation, without speed feedback
1…1000 for asynchronous motor operation as a closed control system with encoder feedback
1…1000 for synchronous motor operation as a closed control system with encoder feedback
1…50 for synchronous motor in positioning operation, without speed feedback
Speed ??accuracy
+/- 0.01% of nominal speed Operation as a closed control system with encoder feedback 0.2 Mn to Mn
+/- 10% of nominal slip without speed feedback 0.2 Mn to Mn
Torque accuracy
+/- 15% for actuating operation, without speed feedback
+/- 5% operation as a closed control system with encoder feedback
short-term overload torque
170% of nominal motor torque +/-10% for 60 s every 10 minutes
220% of nominal motor torque +/-10% for 2 s
Braking torque
<= 150% with braking or lifting resistance
30% without braking resistance
Control profile for synchronous motors
Vector-oriented control, without speed feedback
Vector-oriented control, with speed feedback
control loop
Adjustable PI controller
Slip compensation engine
Can be deactivated
Automatically, regardless of the load
Not available for the U/f characteristics (2 or 5 points)
Adjustable
diagnosis
1 LED (red) for drive voltage
Output voltage
<= supply voltage
isolation
Electrically, between the power and control parts
Cable type for mounting in the housing
With NEMA Type 1 (set): 3 cablesUL 508 cables at 40°C, copper 75°C / PVC
With an IP21 or IP31 kit: 3 cablesIEC cables at 40°C, copper 70°C / PVC
Without mounting kit: 1 Cable IEC cable at 45 °C, copper 70 °C / PVC
Without mounting kit: 1 cable IEC cable at 45 °C, copper 90 °C / XLPE/EPR
electrical connection
Terminal, clamping capacity: 2.5 mm², AWG 14 (AI1-/AI1+, AI2, AO1, R1A, R1B, R1C, R2A, R2B, LI1 - LI6, PWR)
Terminal, clamping capacity: 150 mm² (L1/R, L2/ S, L3/T, U/T1, V/T2, W/T3, PC/-, PO, PA/+, PA, PB)
Tightening torque
0.6 Nm (AI1-/AI1+, AI2, AO1, R1A, R1B, R1C, R2A, R2B, LI1 - LI6, PWR)
41 Nm, 360 lb.in (L1/R, L2/S, L3/T, U/T1, V/T2, W/T3, PC/-, PO, PA/+, PA, PB)
care
Internal supply for setpoint potentiometer (1 to 10 kOhm): 10.5 V DC +/-5%, <10 mA, protection type: overload and short circuit protection
Internal supply: 24 V DC (21…27 V), <200 mA, protection type : Overload and short circuit protection
Number of analog inputs
2
Measuring inputs
AI1-/Al1+ bipolar differential voltage: +/- 10 V DC 24 V max., resolution 11 bit + sign
AI2 software-configurable current: 0 - 20 mA, impedance: 242 Ohm, resolution 11 bit
AI2 software-configurable voltage: 0 - 10 V DC 24 V max., impedance: 30000 ohms, resolution 11 bits
sampling time
2 ms +/- 0.5 ms (AI1-/Al1+) - analog inputs
2 ms +/- 0.5 ms (Al2) - analog inputs
2 ms +/- 0.5 ms (LI1 - LI5) - digital inputs inputs
2 ms +/- 0.5 ms (LI6) when configured as a logical input - digital inputs inputs
reaction time
<= 100 ms in STO (Safe Torque Off = safely switched off torque
AO1 2 ms, tolerance +/- 0.5 ms for analog outputs outputs
R1A, R1B, R1C 7 ms, tolerance +/- 0.5 ms for digital outputs outputs
R2A, R2B 7 ms, tolerance +/- 0.5 ms for digital outputs
absolute accuracy
+/- 0.6% (AI1-/Al1+) at a temperature fluctuation of 60 °C
+/- 0.6% (AI2) at a temperature fluctuation of 60 °C
+/-1% (AO1) at a temperature fluctuation of 60 °C
Linearity error
+/- 0.15% of maximum value (AI1-/Al1+, AI2)
+/- 0.2% (AO1)
Number of analog outputs
1
Type of analog output
AO1 software configurable logic output 10 V 20 mA
AO1 software configurable current 0 - 20 mA, impedance: 500 ohms, resolution 10 bits
AO1 software configurable voltage 0 - 10 V DC, impedance: 470 ohms, resolution 10 bits
Discrete exit number
2
digital output
Configurable relay logic: (R1A, R1B, R1C) NO/NC - 100000 cycles
Configurable relay logic: (R2A, R2B) NO (S) - 100000 cycles
Min. switching current
3 mA at 24 V DC for configurable relay logic
maximum switching current
R1, R2: 2 A at 250 V AC inductive load, cos phi = 0.4
R1, R2: 2 A at 30 V DC inductive load, cos phi = 0.4
R1, R2: 5 A at 250 V AC ohmic load , cos phi = 1
R1, R2: 5 A at 30 V DC ohmic load, cos phi = 1
Discrete entrance number
7
Digital input
LI1 - LI5: programmable 24 V DC with Level 1 PLC, impedance: 3,500 Ohm
LI6: configurable via switch 24 V DC with Level 1 PLC, impedance: 3,500 Ohm
LI6: PTC sensor 0…6 configurable via switch, impedance: 1500 Ohm
PWR: Safety input 24 V DC, impedance: 1500 ohms corresponds to ISO 13849-1 level d
digital logic input
Negative logic (sink) (LI1 - LI5), > 16 V (position 0), < 10 V (position 1)
Positive logic (source) (LI1 - LI5), < 5 V (position 0), > 11 V (position 1)
Negative logic (sink) (LI6) when configured as a logical input, > 16 V (position 0), < 10 V (position 1)
Positive logic (source) (LI6) when configured as a logical input, < 5 V (position 0), > 11 V (position 1)
High and exit ramps
Linearly separately adjustable from 0.01-9000 s
Autom. adjustment. d. Deceleration ramp time b. Overshoot d. Braking poss. using resistance
S, U or user defined
Braking to a standstill
Through direct current supply
Protective functions
Against exceeding the speed limit: Drive
Protection against loss of mains phase: Drive
Interruption detection in the control circuit: Drive
Mains phase interruption: Drive
Overvoltage protection Supply voltage: Drive
Undervoltage detection Mains voltage: Drive
Overcurrent protection between output phases and earth: Drive
Overheat protection: Drive
Overvoltage protection on the DC bus: Drive
Short circuit protection between motor phases: Drive
Thermal Protection: Drive
Motor phase loss: Motor
Power removal – Input: Motor
Thermal protection: Motor
Insulation resistance
> 1 Mohm 500 V DC for 1 minute to ground
Frequency resolution
Analog input: 0.024/50 Hz
Display unit: 0.1 Hz
Communication port protocol
Modbus
CANopen
Plug type
1 RJ45 (on the front) for Modbus
1 RJ45 (on terminal) for Modbus
Male SUB-D 9 on RJ45 for CANopen
physical interface
2-wire RS 485 for Modbus
Transmission frame
RTU for Modbus
Transfer speed
4800,9600,19200 bps, 38.4 Kbps for Modbus on terminal
9600 bps, 19200 bps for Modbus on front
20 kbps, 50 kbps, 125 kbps, 250 kbps, 500 kbps, 1 Mbps for CANopen
Data format
8 bits, 1 stop, even parity for Modbus on the front
8 bits, even odd or no configurable parity for Modbus on terminal
Number of addresses
1…127 for CANopen
1…247 for Modbus
Access method
Slave CANopen
labeling
CE
Operating position
Vertical +/- 10 degrees
Height
630mm
depth
290mm
Width
320mm
Product weight
44kg
Option card
Communication card for CC-Link
controller in programmable card
Communication card for DeviceNet
Communication card for EtherNet/IP
Communication card for Fipio
I/O expansion card
Communication card for Interbus-S
Interface card for pulse generator
Communication card for Modbus Plus
Communication card for Modbus TCP
Communication card for Modbus/Uni-Telway
Trolley card
Communication card for Profibus-DP
communication card for Profibus DP V1
Assembly
Noise level
63.7 dB corresponds to 86/188/EEC
Dielectric strength
3535 V DC between ground and power terminals
5092 V DC between control and power terminals
Electromagnetic compatibility
1.2/50 µs – 8/20 µs Immunity test level 3 corresponds to IEC 61000-4-5
Conducted RF immunity test Level 3 corresponds to IEC 61000-4-6
Electrical radio interference immunity test Level 4 corresponds to IEC 61000-4-4
Electrostatic discharge immunity test level 3 corresponds to IEC 61000-4-2
Testing immunity to radiated high-frequency electromagnetic fields Level 3 corresponds to IEC 61000-4-3
Testing immunity to voltage dips and interruptions corresponds to IEC 61000-4-11
Norms
IEC 60721-3-3 Class 3S2
EN/IEC 61800-3
EN/IEC 61800-5-1
IEC 60721-3-3 Class 3C1
EN 55011 Class A Group 2
EN 61800-3 Environments 1 Class C3
EN 61800-3 Environments 2 Class C3
UL Type 1
Product certifications
GOST
C-Tick
CSA
UL
NOM 117
Pollution level
2 corresponds to EN/IEC 61800-5-1
3 corresponds to UL 840
IP protection)
IP20 on the top part without protective cover on the housing corresponds to EN/IEC 60529
IP20 on the top part without protective cover on the housing corresponds to EN/IEC 61800-5-1
IP21 corresponds to EN/IEC 60529
IP21 corresponds to EN/IEC 61800-5-1
IP41 on the top part corresponds EN/IEC 60529
IP41 on the upper part corresponds to EN/IEC 61800-5-1
IP54 on the lower part corresponds to EN/IEC 60529
IP54 on the lower part corresponds to EN/IEC 61800-5-1
Vibration resistance
1 gn (f= 13…200 Hz) corresponds to EN/IEC 60068-2-6
1.5 mm peak to peak (f= 3…13 Hz) corresponds to EN/IEC 60068-2-6
Shock resistance
15 gn for 11 ms corresponds to EN/IEC 60068-2-27
Relative humidity
5…95% without condensation corresponds to IEC 60068-2-3
5…95% without dripping water corresponds to IEC 60068-2-3
Ambient temperature during operation
-10…50 °C (without performance reduction)
Ambient temperature during storage
-25…70 °C
Operating altitude
<= 1,000 m without power reduction
1000 - 3000 m with power declassification of 1% per 100 m
Packaging units
PU 1 item
PCE
PU 1 quantity
1
PU 1 height
47.0cm
PU 1 width
60.0cm
PU 1 length
80.0cm
PU 1 weight
54.0kg